d.Bu işlemi kolun her iki yanında gerçekleştirin motorlu toprak Frezesi döndürülmesini kolaylaştırmak için ayar demirini
kola göre tamamen oynamasını sağlamak mümkündür; Bunun için kaideyi kaldırın (4).
Set the adjusting iron as explained below in order to obtain optimum milling and ensure the motor-hoe to go forward in the
right direction.
A.Adjustmentfor the hard ground: Loosen the screw (1), lift the adjusting iron in order to take the weight of the motor-hoe to
the back side.
b.Adjustmentfor the soft ground: Loosen the screw (1), lower the adjusting iron in order to transmit the weight of the motor-
hoe to the spindle of the small motor-hoe.During the milling process, the lever carrying the adjusting iron can be adjusted
horizontally as explained below in order that the motor-driven hoe is to move slightly to the sides:
c.Loosen the nut (2) and adjust the screw until it comes to the desired position, tighten the nut (2) again.
d.Perform this process at both end of the lever. It is possible to ensure the adjusting iron to play completely in order to make
the turning ofthe Motor-hoe easy; for this raise the base (4).
TEKERLEK KİLİTLEME POZİSYONLARI (40M ve 5 1M)/TIRE LOCKING POSITIONS (40M and 51M)
Sağ Sol dönüşlü ileri hareket
Sağ ve sol dönüşlü ileri hareketlerde kilitleme mandalı her iki aksta yatay konumda didon istikametine yani B pozisyonuna
getirilmelidir.Emniyet için, toprak frezesi geriye doğru çekildiğinde her iki taraftaki kilitleme mandalının atlama sesi
dinlenmelidir. Her iki taraftaki mandalın atlama sesi işitiliyor ise traktör sağ ve sol dönüş ileri hareket konumundadır.
Sağ ve sol dönüşlü geri hareket
Sağ ve sol dönüşlü geri hareketlerde kilitleme mandalı her iki aksta yatay konumda motor istikametine yani Apozisyonuna
getirilmelidir.Emniyet için, toprak frezesi ileriye doğru itildiğinde her iki taraftaki kilitleme mandalının atlama sesi
dinlenmelidir. Her iki taraftaki mandalın atlama sesi işitiliyor ise traktör sağ ve sol dönüş geri hareket
konumundadır.
Motor çalışması : Kilit mandalları her iki akstada gibi çapraz durumda pozisyonuna getirildiğinde toprak frezesi ileri ve
geri hareket edebildiği gibi her iki yönede dönüşler sağlanabilir.S ağ sol dönüşsüz, ileri ve geri hareketlerde;
Kilit mandalı her iki akstada gibidik konumda D pozisyonuna getirildiğinde sağ ve sol dönüşsüz ileri ve geri hareket
konumundadır.
adal
Forward going with turning right and left.
In the movements goingforward with turning right and left, the locking latch is to be brought in horizontal position on both
axes in the direction of he handle bar that is to B position. For safety, when the motor-hoe is pulled towards back, the sound
of clicking in of the locking latch on both sides is to be heard to. If the sound of clicking in of the latches on both sides can be
heard, then the tractor is in the move of going forward with turning right and left. Reverse going with turning right and
left.In the movements going reverse with turning right and left, the locking latch is to be brought in horizontal position on
both axes in the direction of the handle bar that is to A position.
For safety, when the motor-hoe is pulled towards forward, the sound of clicking in of the locking latch on both sides is to be
heard to. If the sound of clicking in of the latches on both sides can be heard, then the tractor is in the move of going reverse
with turning right and left. Motor running: When the locking latches are brought to the ciosswise position on both axes, the
motor-hoe can not only go forward and backwanis, but also can make turnings in both directions. In the movements of
goingforward and backwards without turning to right and left; when the locking latch is brought to the vertical D position
as on both axes, it is in the position ofgoingforward and backward without turning right and left.
(7)
İlginizi çekebilecek Taral marka Çapa Makinası ürünleri