Kärcher K7 Full Controll Yüksek Basınçlı Yıkama Makinesi
Drawing in water from open reservoi
Full Control System
This high-pressure cleaner is suited to work with the
The pressure indicator on the trigger gun shows the cur-
KÄRCHER suction hose with backflow valve (Optional
rently set pressure level during operation with a Full
accessory, order no. 2.643-100) to draw in surface wa-
Control spray lance.
ter, e.g. from water butts or ponds (see specifications for
Note: The pressure indicator is not significant during
max. suction height).
operation with the T-Racer and other accessories.
Note: With vacuuming operation, the coupling for the
water connection is not required.
Fill the suction hose with water.
Screw the suction hose into the water connection of
the appliance and insert it into the water source
(e.g. rainwater drum).
Bleed the device as follows prior to operation:
MIX
Pressure level
3
2
Turn on the appliance
Unlock the lever Of the trigger gun.
Push the lever of the trigger gun, the device will
switch on.
Let the device run (max. 2 minutes) until the water
exits the trigger gun without bubbles.
Release the lever of the trigger gun.
Lock the lever of the trigger gun.
Operation
A TTENTION
Dry running of more than 2 minutes leads to damage of
the high-pressure pump. If the appliance does not build
up pressure within 2 minutes, switch the appliance Off
and proceed in accordance with the instructions in
Chapter "Troubleshooting".
High pressure operation
CAUTION
Keep a distance Of at least 30 cm when using the jet for
cleaning painted surfaces to avoid damage.
A TTENTION
Car tyres, paint or sensitive surfaces such as wood
should not be cleaned with the dirt blaster, as there is a
risk of damage.
Select a spray lance suitable for the cleaning task.
Illustration
push the spray lance into the trigger gun and fasten
it by a 900 rotation.
Turn on the appliance "I/ON".
Unlock the lever of the trigger gun.
Push the lever Of the trigger gun, the device will
switch on.
Note: Release the lever of the trigger gun; the de-
vice will switch Off again. High pressure remains in
the system.
Full Control Spray lance Vario Power
Turn the spray lance until the LED of the required
pressure level is on at the pressure indicator of the
trigger gun.
HARD
MEDIUM
SOFT
For example, recommended for
Stone terraces made Of paving
stones or exposed aggregate con-
Crete, asphalt, metal surfaces, gar-
den utensils (wheelbarrow, spade,
etc.)
Motorcar / motorcycle, brick sur-
faces, plastered walls, plastic furni-
ture
Wooden surfaces, bicycles, sand
stone surfaces, rattan furniture
Operation with detergent
A TTENTION
The sensitivity Of the materials can strongly differ de-
pending on the age and the condition. The so-called re-
commendations are non-binding.
Operation with detergent
Most KÄRCHER detergents can be bought ready to use
in a Plug 'n' Clean detergent bottle.
Note: Detergent can only be added when the device is
operated in low pressure mode.
DANGER
When using detergents, the material data safety sheet
issued by the detergent manufacturer must be adhered
to, especially the instructions regarding personal pro-
tective equipment.
Remove the cap of the Plug •n' Clean detergent
bottle.
Illustration a
Push the detergent bottle with the opening pointing
downwards into the connection for the Plug 'n'
Clean detergent.
Use Vario Power spray lance.
Turn the spray lance towards "MIX" until the the
LED "MIX" is on on the pressure indicator of the
trigger gun.
Note: This will mix the detergent with the water
stream.
Recommended cleaning method
Spray the detergent sparingly on the dry surface
and allow it to react, but not to dry.
Spray Off loosened dirt with the high pressure jet.
13
İlginizi çekebilecek Kärcher marka Yüksek Basınçlı Yıkama Makinesi ürünleri
