Inoksan FKG042E KONVEKSİYONLU FIRIN Sanayi Tipi Fırın

•  Cihazda tehlikeli bir durum görülmesi halinde,      •  Gaz kontrol düğmesi pilot alev konumuna 
   önce gaz ve elektrik bağlantısını kesiniz, sonra       getiriliyor fakat alev almıyor ise gaz vanasını 
   yetkili servise haber vereniz. Ehliyetsiz kişilerin    kontrol ediniz. Eğer kapalı ise açınız.

   cihaza müdahale etmesine izin vermeyiniz.           •  Cihazın çalışması için tüm işlemleri (ısı seçimi, 
                                                          pozisyon anahtarı konumu, pilotun yakılması) 
                                                          yaptınız fakat cihaz yine çalışmıyor ise kapı tam 

                                                          olarak kapatılmamış olabilir. Kapıyı kontrol edip 
   13. OLASI PROBLEMLER VE ÇÖZÜMLERİ                      kolunun tam yerine oturmasını sağlayınız.

                                                       •  Tüm bunlara rağmen cihaz yine çalışmıyor ise 
•  Enerji lambası yanmıyor ise elektrik şalterini         kontrol panosundaki arıza lambası yanacaktır. Bu 

   kontrol ediniz.                                        durumda yetkili servise haber veriniz ve cihaza 

                                                          hiç bir müdahalede bulunmayınız.


                                                          ÜRÜNLERIN KULLANIM ÖMRÜ 10 YILDIR.



                                                                                                     GB


   Please read these instructions carefully            •  The machine should be fed by 380-400V 3N AC 

   before using the appliance, and retain them            50-60Hz network voltage.

   for future use.                                     •  Use cable of quality H07 RN-F and of crosscut 
                                                          5x1.5mm2
   1. INSTALLATION                                     •  Voltage tolerance should not be more than 

•  Rip off the protective nylon. If any sticky material   ±10%. The machine must be earthed as DIN VDE 
   remains on, clean it with a suitable solvent. (e.g.    0100 clause 540.
   Henkel - Helios)                                       ATTENTION :Make sure that, after the 

•  Settle the appliance under a chimney hood as to        electricity connection, the turning way of the 

   outlet the smoke, smell and the steam that come        fan should be in the arrow direction. If it is 
   out during the cooking.                                reverse, the places of two phases should be 

•  If the smokes will forcedly be thrown out the          changed.
   electrical connection of the aspirator should be 
   common with the appliance. If there is no              4. GAS CONNECTION
   ventilation the appliance should be stopped. At the •  Before making the connection consult the gas 
   same time the absorption quantity should not be        supplier.

   more or less than the gas come out from the         •  Install a fast closing stopcock in an easily 
   appliance.                                             accessible position upline from the appliance.

•  Settle the appliance on a smooth and hard ground    •  Confirm the absence of leaks at the points of 
   with the help of its adjustable bases.                 connection.

•  There should be a space of 60cm. at the left side   •  Confirm that the appliance is suitable for the type 

   of the appliance as to easily make the assembling      of gas with which it will be supplied. If not, read 
   and maintenance. This will also make easy the air      the paragraph “Modification for other type of 
   absorption of the motor. There should also be a        gas”.

   space of 10cm. at the back side for the air 
   circulation.                                        5. MODIFICATION FOR OTHER TYPE OF 
•  While setting the appliance, pay attention that the    GAS
   door of the appliance should be opened minimum      •  The appliance has been adjusted to operate with 
   1100 for an easy load and discharge.                   30mbar LPG(G30).
                                                       •  To adapt the appliance to another type of gas, 
   2. WATER CONNECTION                                    carry out all the operations set out below.

•  Make a water installation of 3/4" to the place      •  The nozzles, the minimum screws of the gas taps 
   where the machine is and connect a spherical           which control the cooktop burners and the 

   valve.                                                 adhesive labels, are contained in a bag supplied 

•  The machine should be fed by 1.5-2 bar water at        with the appliance.

   5-7 0Fh. So, the jet of water will be prevented to     Replacement of burner nozzles (Figure-1)
   be limed in a short time.
   3. ELECTRICAL CONNECTION                            •  Remove the left side sheet.
                                                       •  Unscrew nut which holds the nozzle. Take out “E” 
•  Connect the machine to a network proper to the 
   electric installation standards DIN VDE 0100.          nozzle and choose the most suitable nozzle 
                                                          indicated in table “T2”. Screw the nozzle by nut.



                                                     11