5,2- .001\ı7R,OLLERS
Everi 1.0 hours: check Ae safety and rigidity of the joinas of 'the .mechanism and Light-ness of he cont.roller •wires veri
ofLen, (It' necessary, tıghtar ke bolts, nats and cther joining elements carefully)
At the start of a working hay check
-E.ngine oh level,
-Fuel level in the tank.
Check the oil level in the gearbo.e of the, tractor arıd the hac and make the necessary
1\71:ah,. parts
1),Cias levar
2)Erıgine stop
3)Handie bar adjuster
4)Engine starter lever
5)Air filter
6)Hoe protection cover
7)Blades
8)Spur unit
9)Clutch lever
53- MOTO UN ÇAL1ŞTIRİLMASI VE DURDURULMASI
Motor tanıtına ve kullanma kılavuzuna bakınız, Motoru çalıştırrnadan önce daima şunları kontrol edin.
- Yakıt deposu dolumu?
- Nişli kutusundaki yağ doğru seviyesinde mi? ( )
Motor stop kolu ile kavrama kolu bir yay sayesinde beraberce bloke edilir. (Şekil-4 )Aksi taktirde motor çalışmaz.
Motoru çalıştırmak için kontrol kolunu (start) çalıştırma konumuna getirin. Çalıştırma ipini " E " tutamağından tek
elle kavrayın. ( Şekil-6 ) Yavaşça dişli mandalı tutana kadar çekin ve sonra hızla çekin. Motor bir kez çalıştıktan
sonra tutamağı hemen bırakmayın. ip tamamen sarılıncaya kadar gevşekçe tutun. Sonra gaz kolunu " C " kursun
ortasına getirin. ( Şekil-5 )
5.3- STARTING AND STOPPING THE ENGINE
Read the engine manual. Before starting the engine first check these:
-Is the fuel tank full?
-Is the oil level in the gearbox at the correct position (Figure-3)
Press safety device and clutch lever and lock them with hinge (Figure-4). Otherwise the engine does not start. To start
the engine, adjust the control lever to the working (start) position. Hold the operation rope at the "E" holder with one
hand (Figure-6). Pull slowly until the gear grips the lever and then pull it fast. Once the engine is run, do not release
the handle. Hold it loosely until the rope is completely wound. Then put the gas lever "C" in the middle (Figure-5).
11/1AKİNAYI GERI VİTESE TAKMA
Makinayı geri vitese takmak için önce debriyaj manetini basarak vites kolunu kendinize doğru cekerek vitesi bosa
alın.Vites boşta iken geri vites manetine (sağ manet) bastığınızda (Şekil 4a) vites geri
pozisyonuna geçerek ve makina maneti bastığınız sürece geri gidecektir. Maneti bıraktığınız
anda tekrar kendiliğinden boş vitese geçecektir.
ENGAGING THE REVERSE GEAR Şeki1:4a(Fig:4a)
To use the machine in the reverse gear, push the clutch lever, by pulling the gear lever towards your self put the gear
into the idle position. At idle position when you push the reverse gear lever (right lever) (Figure-4a), the machine
will nın at reverse position as long as you push the lever. Once you release the lever, it will nın at the idle position.
(8)
İlginizi çekebilecek Taral marka Çapa Makinası ürünleri