Na-De 10361 Görüntülü Sesli Kapı Telefonu Sistemi

TS EN
60669-2-1
10361
SPOT TYPE MOTION SENSOR
USAGE AREAS
' At the switch cases
' At the b uilding entrances, stair vestib ules
' At the long halls within the flats
' At the places req uired within the flats
' At covered parking lots
' At the req uisite locations within the hotels
' At the Schools, hospitals, Oil Filling Stations, etc.
"OFFERS ENERGY SAVING FEATURE"  
GENERAL SECURITY CAUTIONS
' Take off the original package and control if there is any damage of transportation and general
view of the product.
' Do not use the product at cross p urposes.
' Keep it away from water and moist areas.
' Do not use the product at d usty, dirty and rusty places.
' Do not supply high voltage.
' Do not apply any liq uid.
' Protect from stroke.
' Using -230-240 V voltage is so dangero us that only the specialist electricians m ust install and
apply.
CAUTIONS FOR INSTALLATION AND USAGE
' Installing m ust be carried o ut professionally in accordance with applicable national wiring
reg ulations and electrical operating conditions.
' Turn of the network before mo unting.
' Do not mo unt the product near the radiator and moist areas.
' Fix the product horizontally to the s urface
' Use 10A fuse the supply inp ut.
' Factory setting; Daylight-darkest / Time - shortest
' Setting can be made 10-15 second after the releasing of the power.
' When a cleaning needed for the product, take of carefully and clean with a dry rag.
' Avoid mounting the detector close to object that can ca use rapid temperature changes such as
heaters, fans, refrigerators and ovens etc, and prevent the detector from point-blank sunshine.
' It can ca use the device operate inaccurately if there is tree, brushes etc. in the coverage area.
SPECIFICATIONS	
103 61
Operating Voltage
-230-240 V / 50 Hz
Angle of Coverage
360 °
Mounting Height
1.8 - 2.8 m. t 20 cm
Detection Range
8 m. t 1 m. (Radi us 4 m.)
Time Setting
10 sec. ~ 1sec. / 10 min. ~ 1 min.
Lighting Load
Max 1000W Incandescent  
Max 400W Fl uorescent
Protection Class
IP20
Operating Temperature
-20 °C - +40 °C
Daylight Setting
The sensor's response threshold can be infinitely varied from 2-2000 l ux.  
If you turn the knob clockwise device will operate at dark.
Control dial set = Daylight operation approx. 2000 l ux.  
Control dial set = Night-time operation approx.2 l ux.
Time Setting
Light ON time can be adj usted contin uo usly from
"10 Sec t 1 sec. / 10 Min t 1 Min.~ If you turn the knob  
clockwise device will operate at minim um time.(10 second)
Control dial set min = Shortest time (10 t 1 sec.)  
Control dial set max = Longest time (10 t 1 min.)
NOTE : Device will a utomatically make its own offset by checking environment for  
approximately 10 min utes after the first installation. After this period device will operate  
normally. If you think the device does not operate normal in first installation, please wait for 10  
min utes and start to test again. Be s ure that there is no motion by this period.
MOUNTING
Connect the line cable to the terminal shown by L  
Connect the neutral cable to the terminal shown by N  
Yo u can also connect the neutral cable of lamp from here  
Connect line cable of the lamp to the terminal shown by LS
Mo unt the body to ceiling part
TROUBLESHOOTING
MALFUNCTION
CAUSE
REMEDY
' No electricity on device
' Fuse fa ulty, not switched on.  
' Short Circuit.
' Fit new fuse: switch ON mains  
switch: check wiring the voltage  
tester.
' Check connections.
' Device will not  
switch ON.
' Daylight setting set to nighttime
mode d uring daytime
operation.
' Bulb fa ulty
' Fuse fa ulty.
' Re-adj ust(Control daylight  
setting).
'Change b ulb.
' New fuse, check connection if  
necessary.
' Device will not  
switch OFF.
' Wind is moving tree and b ushes  
in the detection zone
' Cars in the streets are being  
detected.
' Check detection zone and  
re-adjust if necessary  
'Change detection zone
' Change in device reach
' Differing ambient  
temperatures
' Use shro uds to define  
detection zone precisely
DETECTION AREA
Detection area of motion sensors depends on the angle between PIR detector and moving  
direction, temperature, mounting style and mounting
places.
Temperature is very important for operation of motion sensors like all electronic devices. Using  
higher val ue of loads written on manuals and packages will decrease temperature inside the device  
when using Na-De Motion Sensor. As a res ult detection range will decrease  
and may ca use defect of electronic components. Environment temperature will also ca use  
decrease of detection range. Detection range given is determined at 20 °C .If the weather is hot, it  
will decrease.
Detection range is determined at the temperature of 20 °C.
SETTINGS
max	
min
Ceiling	
,s _ za m t z~ ~
8 m : 1 m
Use this part surface mo unt aparate) when making s urface mo unt  
Place the aparton the ceiling shown by (a)  
Pass the cables thro ugh the hole shown by (b)
(a)
(b)
DETECTION AREA
L N LS
Walking tangential to the sensor
(normal detection range)	
Figure 1
Walking directly to the sensor 
(lover detection range)
The maxim um detection range can be realized when walking tangential to the sensor  
(Figure 1). When walking directly to the sensor detection range will be low. Because yo  
will not be able to cut vertical areas. Detection range of Na-De Motion Sensors is  
8 meters as diameter 4 meters as radi us.
This item is prod uced according to 73 / 23 / EEC(Low Voltage Directive) and  
89 / 336 / EEC (Regulations of Electromagnetic Harmony).
For further information, please call : 0800 2 61 78 05
info~na-de.com.tr	
www.na-de.com.tr