Fakir CLARRIS Elektrikli Süpürge

  B-Preparing the vacuum cleaner for operation                12- Setting 5 – vacuuming hard fl oors and crevices. 

                                                                  Set the desired power value by pressing the power 
  1- Insert the curved hose end in the opening of the             adjustment buttons , (11,9).
     vacuum cleaner and gently press. A characteristic 
     click indicates that the hose has been properly installed.C-SAFBAG dust bag disassembly/assembly
  2- Connect the other end of the hose (handle) with the 
     telescopic suction tube.                                 1- The vacuum cleaner is equipped with a dust bag full 
  3- Adjust the length of the telescopic suction tube by         indicator (8). When the dust bag full indicator (8) 
     sliding the slider according to the arrow and pull          lights~ during operation (with the nozzle or the brush 
     out/pull the tube together.                                 lifted above the cleaned surface) it means that the 
 4- Assemble the appropriate nozzle or brush to the other        bag is full and needs to be replaced. In addition the 
     end of the suction tube.                                    dust bag full indicator (8) may activate if the suction 
 5- You may assemble a basket for picking up small               hose or the elements attached to the suction hose are 
     objects in the combination brush with the small item        clogged (suction power – level 5).
     separator. In order to do so remove the blank cover      2- Switch off the vacuum cleaner by pressing the 
     and insert the basket.                                      “on/off” button (7) and unplug the appliance 
 6- To clean hard surfaces – wooden fl oors, plastic fl       3- Press the two side buttons on the end of the hose 
     oors, ceramic tiles etc. pull out the brush by pressing     andremove the hose end from the inlet opening 
     the switch on the combination brush according to the        of the vacuum cleaner.
     fi gure .                                                4- Release the upper cover fastening (12) and open 
 7- The vacuum cleaner is equipped with an accessory             the cover.
     compartment. To open the compartment, lift the           5- Remove the SAFBAG dust bag module (18) from 
     compartment lid and pull it downwards.                      the vacuum cleaner chamber.
 8- Grab the plug (3) and pull the cord out of the vacuum     6- Grab the dust bag cover, gently bend it towards 
     cleaner.                                                    the inside and remove the whole dust bag upwards. 
                                                              7- Insert the plate of the new dust bag in the tracks 
                                                                 of the SAFBAG dust bag module (18) and slide it 
                                                                 until stop. The direction for inserting the dust bag 
              CAUTION!                                           is indicated by the arrow on the bag.

                                                              8- Slide the SAFBAG dust bag module together with 
     While pulling out the cord pay attention                    the installed bag in the tracks located on the side 
     to the yellow stripe which signals the end of the           of the vacuum cleaner chamber. Close the cover 
     cord. Further attempts (pulling on cord) may result         by pressing it until you hear a characteristic clickpay 

     in damaging the cord.                                       attention not to trap the dust bag.




 9- Plug in the appliance. Before operation make sure 
     that the SAFBAG dust bag module is installed in the                   ATTENTION!
     vacuum cleaner chamber and that all fi lters are 
     installed in the appliance.                                 Do not vacuum without the SAFBAG dust 
10- Switch on the vacuum cleaner by pressing the “on/off”        bag module installed in the appliance. The lack 
     button (7).                                                 of the SAFBAG dust bag module prevents from 
11-The vacuum cleaner is equipped with an electronic             locking the upper cover of the appliance.
     power control which allows to gradually adjust the 
     vacuum cleaner suction power during operation. To 
     adjust the suction power use the power adjustment         Fakir vacuum cleaners are equipped with SAFBAG dust 
     buttons (11,9) – to increase the suction power or – to    bags in the amount indicated in the table. It is 
     decrease the suction power. The suction power setting     recommended to replace the dust bag if:
     is indicated by the appropriate number of lit diodes.     a) the dust bag full indicator lights up,
     The vacuum cleaner will by default begin operation        b) the vacuum cleaner operates poorly,

     at the medium power range. 4 diodes will light on         c) the dust bag is full.

     the power level indicator (10).                           Filter disassembly
     The suction power may be adjusted during operation. 
     The recommended settings are:                             Before changing the fi lters make sure that the vacuum 
     Setting 1 – vacuuming curtains                            cleaner is switched off and unplugged from the mains 
     Setting 2 – vacuuming upholstery                          supply.

     Setting 3 – cost-effective power
     Setting 4 – vacuuming carpets 
                                                          05