Blue House BH911RC Vantilatör
Important Safeguards • Do not use outdoors • The fan's direction can be adjusted relative
When using electrical appliances, basic safety • This product is intended for household use to the base by loosening the Thumb Screw at
precautions should always be followed including ONLY and not for commercial or industri- (al the bottom of the Motor Assembly, and
the following use rotating the Fan Head.
Please read all instructions before using this fan. • This fan is equipped with GS safety plug. Never • To set the fan into oscillation, depress the
• Use fan only for intended use as described in connect the fan to any power source (other Oscillation Knob on the top of the Motor
instruction manual than a 230 volt alternating current polarized Assembly. The Fan Head will pivot side-to-
• To protect against electrical shock do not outlet. side and up and down . For stationary
place fan in window, immerse fan, plug or • " If the supply cord is damaged, it must be operation, pull up on the Oscillation Knob.
(cord into water or spray with liquids, replaced by the manufacturer or it's Service
• Close supervision is necessary when any agent or a similarly qualified person in order READ AND SAVE THESE INSTRUCTIONS
appliance is used by or near children to avoid a hazard."
• Unplug from outlet when not in use, when Warning: To reduce the risk of fire or electrical
moving fan from one location to another, Operation shock, DO NOT USE THIS FAN with any SOLID
(before putting on or taking off parts, and • Place the assembled tan on a flat, level firm STATE Fan Speed Control Device.
before cleaning. and dry surface.
• Avoid contacting moving parts • Plug the Power Cord into a polarized 230 volt
• Do not operate in the presence of explosive AC wall outlet
and or flammable fumes • Turn the fan on and select the desired running
• Do not place fan or any parts near an open speed with the Speed Control Switch
flame, cooking or other heating appliance. conveniently and safely located at the front
• Do not operate with a damaged cord or plug of the fan below the Front Grill
01 after the fan malfunctions, or has (been • To adjust the fan s height, loosen the Height
dropped or damaged in any manner Adjustment Knob by unscrewing counter-
• The use of attachments not recommended or clockwise only a few turns. Pull upward on
sold by Sonifer may cause hazards. the chrome portion of the Pole Assembly
• Do not let cord hang over edge of table or while holding the lower portion firmly to
counter, or touch hot surfaces. raise the height, or push down on the chrome
• To disconnect, grip plug and pull from wall portion to lower. Retighten the Height
outlet. Never yank on cord. Adjustment Knob,
• Always use on a dry, level surface being careful not to overtighten To
• Do not hang or mount fan on a wall or ceiling • To adjust the normal upward or downward
• Do not operate without fan grills properly in tilt of the Pan Head, loosen the Tilt Knob on
place. the side of the Motor Assembly and carefully
lift or lower the head angle while holding the
Rear Grill Handle Do not force the head. Re-
tighten the lilt Knob when the desired angle
is found
7 8
Arka Izgara Kulp
Ön Izgara Kancas› Motor Mili
Assembly • Fully open the 3 clips around the outer edge 4. Final Assembly
I. Remove all parts from the carton: Ön Izgara Klipsi (3) Motor of the Front Grill, then hang the Hook at the • Twist the Thumb Screw at the bottom of the
• Motor Assembly, including: Montaj› top of the Front Grill over the top of the Rear Motor Assembly counter-clockwise until (no
(-Grill Nut and Blade Knob Grill as depicted. Push the clips inward over threaded portion is visible within
• Grill Set, Front and Rear the Grill Assembly and the Fan Head Assembly • Place the chrome end of the Pole Assembly
• Fan Blade is now complete. within the hole at the bottom of the (Motor
• Pole Assembly Assembly and fully insert If the Pole will not
• Base 3. Base Assembly fully insert, the Thumb Screw (must be further
• Component pack, including • Remove the Height Adjustment Knob from loosened Twist the Thumb Screw clockwise
- Bolts (3) the Pole Assembly by unscrewing (counter- to tighten the Motor (Assembly to the Pole
- Wing Nuts (3 ) clockwise. and Fan Assembly is now complete
- Bolt Plate • Slide the Bolt Plate over the small end of the
- Cover Pole Assembly The Embossed Ring on (the Care, Cleaning & Storage
Kanat Bolt Plate should face the small end of the • The Fan Blade and Grill Set should be cleaned
2. Assemble Fan Head Dü¤mesi Izgara Pole so that the bottom of the Bolt (Place is regularly for most efficient operation
Somunu
• Remove the Grill Nut and Blade Knob from flush with the bottom of the Pole. Unplug the fan. then reverse the assembly
the Motor Assembly, note that the Blade Knob Ön Izgara Pervane Yükseklik • Tipping the Base on one side and holding the procedure to remove those parts from the
is reverse threaded. Turn clockwise to remove Kanad› Ayar Pole horizontally, place a Bolt through (a Motor Assembly before cleaning. Wipe with
from the Motor Shaft. Dü¤mesi square hole of the Bolt Plate then through a a damp cloth, then towel dry
Kapak
• Place the Rear Grill over the Motor Shaft and hole at the center of the Base. The (threaded • Never immerse any (an components in water
onto the Motor Assembly noting that the Civata (3) end of the Bolt should extend from the bottom Wipe the fan only with a dry or slight!)
handle should be positioned toward the top Civata Plakas› of the Base Attach a Wing (Nut to the Bolt- moist cloth, then immediately towel dry
of the fan. The small plastic pin of the Motor do not fully tighten. Align the remaining 2 • Always store the fan in a cool dry location
Assembly should be aligned with the hole in holes on the Bolt Plate with (the matching
the Rear Grill. Reattach the Grill Nut, turning holes of the Base and attach the remaining
clockwise to secure the Rear Grill to the Motor Kutup Bolts Wing Nuts. Fully tight (en all Wing Nuts
Assembly. Montaj› • Slide the Cover over the small end of the Pole
• Align the Motor Shaft with the "D" shaped to cover the Bolt Plate as depicted
hole of the Fan Blade. Fully insert the Motor • Screw the Height Adjustment Knob back onto
Shaft into the Fan Blade, then secure with the the Pole Assembly as shipped. Base (Assembly
Blade Knob, turning counter-clockwise. Do is now complete.
not overtighten.
PUSH CLIPS TO ASSEMBLE GRILL Taban
9 10