Blue House BH910RC Vantilatör
Operation Instructions 5. Install the fan blade(5) onto the shaft with the
READ AND SAVE THESE INSTRUCTIONS cutouts fitted on the retaining pin.Screw the
spinner(4) onto the motor shaft counter
CAUTION: clockwise.
Read Rules Carefully for Safe Operation and 6. Press the rim of the front guard (2) onto the
Instructions. rear guard (7) until the front guard (2) is
properly fitted.
WARNING: 7. Secure both guards firmly by tightening the
If the supply cord is damaged, it must be replaced circlip(3) then close the clips.
by service agent ara similarly qualified person
in order to avoid a hazard. ASSEMBLY OF COLUMN
Take (14) the base and (11+12+13) column parts
RULES FOR SAFE OPERATION from the packing box and loose (15) the nut. Fix
1. Da not leave the fan running unattended. the column on (14) the base using (13) the nut.
2. Never insertfingers, pencils, or any other object Unscrew and take off the height adjusting knob,
through the grille when fan is running. mount the column parts, and screw the height
3. Disconnect fan when moving from one location adjusting knob ta tighten the extension column
to another. in an appropriate position .
4. Disconnect fan when removing grilles for
cleaning. Operating Instructions
5. Be sure fan is on a stable surface when 1. Place the fan on a stable surface before
operating to avoid overturning. operating. Plug in the fan.
6. DO NOT use fan in window. Rain may create 2. Ta adjust the angle (up/down) of the airflow,
electrical hazard. tut the head up or down to the required
position smoothly.
ASSEMBLY OF BLADE AND GRILLES
1. Unscrew the spinner (4) and the plastic nut (6)
counterclockwise from the front of the motor
housing (8) then remove both of them.
2. Set the rear guard (7) in the proper position
with handle up.
3. Screw the plastic nut(6) firmly onto the
projecting thread on the motor housing(8), by
rotating clockwise and tighten firmly.
4. Remove and discard the plastic sleeve on the
7 motor shaft.
On the fan control panel, there are several INSERT BATTERIES OSCILLATING
keys. 1. Press down on the battery compartment (over Ta make/stop the fan head oscillate,push
On/Off ( el_)) and slide it out. down/pull up (9) the oscillating knob.
Speed (,", ) 2. Insert the batteries, making sure that the
Timer (C)) positive terminals are facing the proper way. FAN UPWARD AND DOWNWARD AIR BLOW
3. Replace for cover. Gently press or lift the net cover to change the
On/Off ( ) NOTES: Use size "AAA" manganese of alkaline upward and downward angles when adjusting
Press this key to turn on / off the fan. batteries. Do not use rechargeable batteries. the upward and downward air blow.
(The fan is started at medium speed, after 2
seconds it will automatically shift to the low USING THE REMOTE CONTROLLER CORRECTLY CLEANING
speed.) 1. Point the remote controller at the receptor on 1. Be sure to unplug from the electrical supply
the base of fan stand and press the desired source before cleaning.
Speed (1. ) button. 2. Plastic parts should be cleaned with mild soap
Press this key to select you fan speed (1, 2, 3). 2. The remote controller will work at distances and a damp cloth or sponge. Thoroughly to
of up to roughly five meters and the angle of remove soap film with clean water.
Timer ( C) ) 60 degree between right and lefit from the 3. Be sure not to make water or other liquid enter
Press this key to set the fan operation time. receptor. inside of motor.
Maximum timer time is 4 hours. Press the timer 3. Avoid the sunlight directly irradiate the
key will increase the timer time. The sequence receptor so as ensure receiving effect.
is 1, 2, 4, and timer off. Number shown on the 4. The batteries must be removed from the
control panel shows the timer time. Na number remote controller before it is scrapped, and
means timer off. that they are disposed of safely.
REMOTE CONTROLLER OPERATION
These key of control switch may use as same as
manual control panel operation,
NOTE:The remote controller is only used in
BH91ORC.
10