Blue House BH564MG Et Kıyma Makinesi
INTRODUCTION 5. Do not use the appliance if the mains cord, the 20.This appliance is not intended for use by
Iliis appliance k equipped with a thermostat plug or other parts are damaged. persons (including children) with reduced
system. This system will autorrFatically cut off the 6. If the rnains cord of this appliance is damaged, physical, sensory or mental capabilities,or lack
povver supply to the appliance in case of it muse always be replaced by rrtanufacture or of experience and knowledge, unless they
overheating. a service center authorized, in order to avoid have been give supervision or instruction
If you appliance suddenly stops running: hazardous situations. concerr-Fing use of the appliance by a person
1. Pull the mains plug out of the socket. 7. Thoroughly clean the parts that will come into responsible for their safety.
2. Press the switch button to turn off the contact with food before you use the appliance 21.Children should be supervised to ensure that
appliance. for the first time . they do not play with the appliance.
3. Le t the appliance cool down for 60 minutes. 8. Unplug the appliance immediately atter use. 22.If the appliance is locked, please press Reversal
4. Put the mains plug in the socket. 9. Never use you finger or an objection to push button (REV). The meat locked in cutter
5. Switch the appliance on again. ingredients down the feed tube while the housir-Fg is untrodden, so the appliance can
Please contact your dealer of an authorized service appliance is running. Only the pusher is to be renew is usual condition.
center if the thermostat system is activated too used for this purpose.
of-ten. 10.Keep the appliance out of the reach of
If you plug in, the indictor light will be on. children.
CAL0770N: in order to avoid a hazardous situation, 11.Never let the appliance run unattended.
this appliance must never be connecteci to a time 12.5witch the appliance off before detaching and
switch. install any accessory.
13.Wait until moving parts have stopped running
IMPORTANT before you rernove the parts of the appliance.
1. Read these instructions for use carefully and 14.Never immerse the motor unit in the water
look at the illustrations before using the or any other liquid, nor rinse it under the tap.
appliance. Use only a moist cloth to clean the motor unit.
2. Keep these instructions for future reference. 15.Do not attempt to grind bones, nuts or other
3. Check if the voltage indicated on the appliance hard items.
corresponds to the local mains voltage before 16.Never reach into the cutter housing. Alvvays
you connect the appliance. use the pusher.
4. Never use any accessories of parts from other 17.Never operation the appliance continuously
manufacture .Your guarantee will become for more than 3 rninutes at 600W.
invalid if such accessories or parts have been 18.Accessories shall include instructions for their
used. safe use.
19.1t shall vvarn of potential injury from rnisuse.
11 12
6. Place the hopper plate on the head and fix it
INSTRUCTION FOR USE into positi on.
Assembling o 7. Locate the unit on a firm place.
1. Press the fasten button'hold the head and Insert 8. The air passage at the bottorn and the side of
it into the ir-Flet when inserting please pay the motor housing should be kept free and not
attention the head must be slanted as per , ------ blocked.
arrow indicated on the top, see (fig.1), then
move the head anticlockwise sa ta t the head Mi ncer
being fastened tightly. (lig 2) 3 4 1. Insert the worm shaft into the cutter housing,
2. Place the snake into the head, long end first, the plastic er-Fd first.
and turn to feed the screw slightly until it is Place the cutter un it onto the worm shaft. (The
set into the motor housing (fig.3). cutting edges should be at the front ) Place
3. Place the cutting blade onto the snake shaft the medium grinding disc or coarse grinding
with the blade facir-Fg the front as illustrated i disc (depending on the consistency you prefer)
i
(fig.4). If it is not fitted properly, meat will not onto the worm shaft. (M ake sure the notch of
be grinded. the grinding disc fit onto the projections of
4. Place the desired cutting plate next to the the rrtincer head.) Turn the screw ring in the
cutting blade, fitting protrusions in the slot 5 6 direction of the arrow on the cutter housing
(fig.5). until it is properly fastened.
5. Support or press the center of the cutting plate 2. Attach the cutter housing to the motor unit.
with one finger then screw the fixing ring tight 3. Place the tray on the upright part of the cutter
with another hand (fig.6). Do not over tighten. housing.
4. Now the appliance is ready for rnincing.
Cut the meat into 10cm-long, 2cm-thick strips.
Remove bor-Fes, pieces of gristle and sinews as
7 much as possible. (Never use frozen meat[
Put the meat in the tray. Usethe pusher to gently
push the meat into the cutter hosing. (For steak
tartare • rnince the meat with the medium
grinding disc twice. )
Ilik.
13 14