VACUUM CLEANER WITH WATER FILTER TECHNICAL SPECIFICATIONS WARNING: Mount the pieces completely as explained in the manual. Otherwise the lifetime of your
Read Before Using The Machine; product will be shorter.
1- 1-Use your Water Filtered Vacuum Cleaner only on the grounding plug in compliant with 10 A current.
2- Before carrying out any maintenance works, you must unplug.
3- CAUTION: Do not vacuum any flammable materials like gasoline, lubricant, alcohol and thinner.
4- CAUTION: Do not vacuum materials with temperature over 60°C like burning cigarette, ash, hot coal
and etc.
5- CAUTION: Powder injurious to health (asbestos powder and etc.) should not be vacuumed.
6- If the cable insulation is damaged, it should be changed by authorized service. Do not use your machine
with damaged cable.
7- Filters should be always kept clean. If the filters are kept clean, your machine will operate with Figure 2 Fixing the sponge filter
rnaximum vacuum.
8- Filters should be used in accordance with their purpose.
9- Since products like detergent, soap powder may foam water and thus cause the water access to the
engine; in case you vacuum such materials, turn off your machine and rinse the bucket. Figııre 1
10- Clean any residuals which may accumulate like dust, mud and etc by power washing the water filter Figure 3 Figure 4
pipe.
INSTALLATION AND USAGE
After you get the machine out of its package, by opening the fixing latches, separate the motor part from
the transparent frame (Figure 1). Afterwards, place the sponge filter to the motor part (Figure 2). Then
place the water tank to the transparent frame (Figure 3). Fix the water filter pipe to the water filter
placement bed in the water tank (Figure 4). Put 1 Lt of water to your product as seen in Figure 5. Place
the wave breaker unit sponge filters to the wave breaker unit (Figure 6). Insert the wave breaker unit
as shown in Figure 9. Fix the motor part with the transparent frame by means of the locking latches.
Mount the dry cleaning heading, extension pipes, vacuum adjustment pipe bend, vacuum hose and the Figure 6
hose heading. You can use the other cleaning apparatuses included in our product by installing them in
accordance with your cleaning purposes.
Figur., 5
7 8
CLEANING AND MAINTENANCE POSSIBLE PROBLEMS AND THEIR SOLUTIONS
By opening the locking latches connecting the transparent frame take the motor part out. Afterwards, take Problems you may encounter regarding your product and methods of solutions to be applied without
the wave breaker unit and the water tank out. Wash the sponge filters in the wave breaker unit. Because it applying to your service are stated in the following table.
may lead to deformation, do not wash the filters with very hot water or in the washing machine. Dry your
filter in natural environment. Fill out the dirty water in the water tank and rinse it (Figure 8). Check if there is TROUBLESHOOTING TABLE
any congestion or not by taking the water filter pipe out of the water tank. You can take the dust, dirt, etc.
from the product by passing water with the tap through the pipe. Take the sponge filter in the motor part
and wash with water. Clean the exhaust filter that is at the back of the motor part weekly (Figure 7) Do not
reuse your filters before they are totally dry.
IDENTIFICATION OF
WET USAGE PROBLEM
To get your machine ready for wet usage, disassemble the engine section from the transparent trunk. Check
the sponge filter and be sure it is fixed. Then place the water tank. Place the water filter pipe and the wave THE VACUUM OF There may be blockages in Check the carpet hard floor
breaker unit. Connect the motor part and the transparent frame with the fixing latches. The washbasin THE PRODUCT IS the apparatuses installed in cleaning head (12), vacuum adjustable
congestion problems may be solved by absorbing the materials that accumulated on various floors by the REDUCED/ IT DOESN'T the product. pipe bend (11) water filter pipe.
machine by means of the vacuum pipe and suction adjustment pipe bend. 0M-ter the suction process, the water VACUUM There may be blockage in these parts.
in the reservoir should not be kept. {)
The filters might be blocked. Check the sponge filter of wave breaker
WARNING: unit (19), sponge filter (15), exhaust
Never remove the sponge [ilter whether in dry and wet cleaning. filter (27). If there is any blockage, clean
it in accordance with the instructions.
FILTERS
Sponge Filter: Sponge filter must be installed in dry and wet vacuuming. Otherwise, dust or large particulars
will access to the turbine and thus, damage the engine. If we carry out water suction process, the water will The vacuum hose (9) might Install your vacuum hose (9) into the
totally access to the turbine. In this case, the guarantee shall be invalid. Regular maintenance should be carried not be installed properly into hose housing (6) properly.
out regarding the sponge filter which is designed for long-term usage. Since filters which are left wet will wear the hose housing (6).
out easily, let them dry after washing.
MY PRODUCT GIVES The exhaust filter rn ight be Remove the exhaust filter (27) and check
Sponge Filter of Wave Breaker Unit: It prevents the water access from the air voids in the wave breaker OFF DUST WHILE IT blocked. it. It might be blocked because of dust.
unit during dry vacuum cleaning. These filters should be totally dried before each usage. OPERATES. Clean your filter and install it in
Exhaust Filter: The exhaust filter installed in your machine as shown in Figure 7 prevents the dust leakages and accordance with the instructions.
microbe bacteria's resulted by air circulation during dry cleaning to mix into the air. When the filter gets dirty,
wash it under the sink by gently squeezing it. The filter lid is opened by sliding it from bottom and it's placed
from the bottom and pressed from the top and closed.
9 10
İlginizi çekebilecek Blue House marka Elektrikli Süpürgeler ürünleri
