Fig 6 y Button Before liquid suction you must change the carpet
Telescopic Tube brush with the Water Brush
Main Brush
When you finish, empty the tank completely and
vacuum up about one Ilter of clean water to rinse
Power clean the inside of the Flexible Hose and the
Button Telescopic Tube. Repeat if necessary.
Decrease Button
To dry the inside of Hose & the Tube, detach the
Detachable Soft Water Brush, and run your machine for a few minutes
Base withoutsucking up any dirt. Wash and dry the water
•The suction power class is indicated by the brush separateiy.
numbers of green indicating lights. For example: 3. Telescopic Tube 6. Multi Duster Brush
three green lights means the suction power is • The extendable Telescopic Tube gives you added The Multi Duster Brush (2 in 1) is for removing Vacuum soapy liquid or detergentshould be avoidect
now at the 3rd high position. (total 4 positions.) flexibility and control. Depending on your dust from all type of surfaces such as lampshades, as this causes frothing inside the water tank.
application and situation, you may adjust the electric equipment, air conditioner grills, car
Use of your product length of the Telescopic Tube to suit your needs. dashboards etc. Separately it can be used as a 8. Air-Blow Function
1. Standby Button Push and hold the locking knob, extend or sofa nozzle. • You may convert your machine to blow air out
• This button is used to switch between standby retract the telescopic pole as required. Release by attaching the Flexible Hose to the machine's
mode and operation mode. The initial push the knob and pull the extended tube slightly Fig.8 air outlet socket. See "Product Care and
turns the suction power on at the low mode. to lock it in place. Storage" on how to remove the Air Outlet Grill.
While the machine is operating, push this 4. Crevice Tool • The Blower Function is recommended for use
button returns the machine to the standby Use this accessory tool for corners, crevices and to gather scattered dry waste such as leaves
mode. cracks. and confetti or any other purpose.
2. Suction Power Selection Button S. Main Brush & Turbo Brush • Together with the spray bottle, you can spray
• There are four suction power setting, Low, Connect the main brush and the turbo brush 7. Water Brush & Liquid Suction water or other liquid for many purpose use.
Medium, High and Turbo. Use (+) or (-) button to the telescopic tube , you can clean the carpet The Water Brush is so versatile that it can be used Pls combine the spray bottle with the hose
on the main body of the machine to select the and floor. To protect the floor, you can assemble for vacuuming both solid and liquid dirt and is handle. Driving the vacuum machine, and using
desired setting. the soft base to the main brush. mainly for use on hard floor surface. your finger to push the hole on the top of the
• The suction power class is indicated by the bottle to switch the spraying.
numbers of green indicating lights. For example: Caution: if you use your machine for liquid suction. 9. Automatic Cord Storage
three green lights means the suction power is Make sure you first reduce the amount of water in Your system comes with an Automatic Code
now at the 3rd high position. (total 4 positions.) the tank by about half. It is also important not to Storage system. Push the button at the back of
allow the tank to become too full of vacuumed the machine and the cord is retracted
liquid. automatically. The large button also allows this
15 to be done with your foot. 16
Troubleshooting
Do not disassemble or attempt to repair the machine yourself
Caution: While nearing the end of the retraction, • Regularly dismantle and clean the filter • Remove the HEPA Filter from the frame and
hold on to the end of the cord and guide it into the assembly. insert a new one or wash it. Conditions Possible Cause and Solution
cord storage compartment. The force and speed of • Remove the curved tube by pulling it from the
the retraction may cause the plug to snap back and meshed filter cage. 4. Air Outlet HEPA Filter
hit something. • Pull out the filter cage and remove the sponge • Push the button on the Air Outlet Grill, remove • The machine stops • Wait for about 30 seconds before
filter. Wash and rinse all the components. Dry the Air Outlet Grill from the body. during operation and you operate the machine again. This lets the
Product Care and Storage before assembling them. (Note: the sponge • Take out the Air Outlet HEPA Filter. all four suction power machine reset whilst you identify one of the
Always switch off the main switch and disconnect filter must be equipped on the filter cage during • Replace with a new one or wash it. It is indicator lights start following possible causes.
the AC cord from the electrical outlet before cleaning working the machine.) recommended to have a wash or replace a new blinking together. • The water has turned very dirt and mirky.
you machine or replacing any part. • To remove stubborn dirt from the container one each half year. Empty the water container and replace with
1. General and the filter assembly, use normal washing- clean water.
• You may wipe the machine with a damp cloth. up liquid but make sure it is rinsed thoroughly Fig 13 • The water level is above the maximum level.
Synthetic detergent may be used on plastic and afterwards. Reduce the water level.
metal parts if necessary. Make sure you wipe 3. Front HEPA Filter • The selected suction power level is too high
the machine and its parts dry before storage. • if there is a noticeable drop in the suction for the current cleaning application. Reduce
• Do not use strong cleaning agents such as power, this is an indication that the HEPA filter the suction power.
Push Here • The airflow is blocked. Remove the blockage.
benzene or thinner to clean the machine. needs to be changed with a new one or to be
• Always store your product and parts after they washed.
are completely dried. • Pull the Cover Release Level upwards and lift
up the Tank Cover. , then remove the • The machine does • AC supply is not properly connected the AC
2. Cleaning and Maintenance of the filter water tank, take out the HEPA Filter not start cord to electrical supply.
assembly. Frame.
• It is high recommended that you pour away
the dirty water and clean the container and Fig 11 HEPA
Filter Frame • Noticeable decrease • The HEPA filter requires replacement. Change
the filter assembly after each use. Keeping your Caution: Use only original spare port. in the suction power a new one.
home clean using a clean appliance is an 5. Storage
• There is a blockage. Remove the cleaning
advantage that the machine has over 'bag'- • Store your machine with care and in a cool dry
tools and attachments from the machine and
vacuum cleaner. place.
remove the blockage.
• To empty the water container, pull the Cover
Release Level upwards.
• Lift up the cover and pull out the filter assembly
and remove the water tank with the handle • Leakage of water when • The Switch Float is blocked. Unblock it by
on the tank. using for cleaning of cleaning.
• Empty the container and clean, rinse and leave liquid waste.
to dry.
17 18
İlginizi çekebilecek Blue House marka Elektrikli Süpürge ürünleri