B-Preparing the vacuum cleaner for operation 12- Setting 5 – vacuuming hard fl oors and crevices.
Set the desired power value by pressing the power
1- Insert the curved hose end in the opening of the adjustment buttons , (11,9).
vacuum cleaner and gently press. A characteristic
click indicates that the hose has been properly installed.C-SAFBAG dust bag disassembly/assembly
2- Connect the other end of the hose (handle) with the
telescopic suction tube. 1- The vacuum cleaner is equipped with a dust bag full
3- Adjust the length of the telescopic suction tube by indicator (8). When the dust bag full indicator (8)
sliding the slider according to the arrow and pull lights~ during operation (with the nozzle or the brush
out/pull the tube together. lifted above the cleaned surface) it means that the
4- Assemble the appropriate nozzle or brush to the other bag is full and needs to be replaced. In addition the
end of the suction tube. dust bag full indicator (8) may activate if the suction
5- You may assemble a basket for picking up small hose or the elements attached to the suction hose are
objects in the combination brush with the small item clogged (suction power – level 5).
separator. In order to do so remove the blank cover 2- Switch off the vacuum cleaner by pressing the
and insert the basket. “on/off” button (7) and unplug the appliance
6- To clean hard surfaces – wooden fl oors, plastic fl 3- Press the two side buttons on the end of the hose
oors, ceramic tiles etc. pull out the brush by pressing andremove the hose end from the inlet opening
the switch on the combination brush according to the of the vacuum cleaner.
fi gure . 4- Release the upper cover fastening (12) and open
7- The vacuum cleaner is equipped with an accessory the cover.
compartment. To open the compartment, lift the 5- Remove the SAFBAG dust bag module (18) from
compartment lid and pull it downwards. the vacuum cleaner chamber.
8- Grab the plug (3) and pull the cord out of the vacuum 6- Grab the dust bag cover, gently bend it towards
cleaner. the inside and remove the whole dust bag upwards.
7- Insert the plate of the new dust bag in the tracks
of the SAFBAG dust bag module (18) and slide it
until stop. The direction for inserting the dust bag
CAUTION! is indicated by the arrow on the bag.
8- Slide the SAFBAG dust bag module together with
While pulling out the cord pay attention the installed bag in the tracks located on the side
to the yellow stripe which signals the end of the of the vacuum cleaner chamber. Close the cover
cord. Further attempts (pulling on cord) may result by pressing it until you hear a characteristic clickpay
in damaging the cord. attention not to trap the dust bag.
9- Plug in the appliance. Before operation make sure
that the SAFBAG dust bag module is installed in the ATTENTION!
vacuum cleaner chamber and that all fi lters are
installed in the appliance. Do not vacuum without the SAFBAG dust
10- Switch on the vacuum cleaner by pressing the “on/off” bag module installed in the appliance. The lack
button (7). of the SAFBAG dust bag module prevents from
11-The vacuum cleaner is equipped with an electronic locking the upper cover of the appliance.
power control which allows to gradually adjust the
vacuum cleaner suction power during operation. To
adjust the suction power use the power adjustment Fakir vacuum cleaners are equipped with SAFBAG dust
buttons (11,9) – to increase the suction power or – to bags in the amount indicated in the table. It is
decrease the suction power. The suction power setting recommended to replace the dust bag if:
is indicated by the appropriate number of lit diodes. a) the dust bag full indicator lights up,
The vacuum cleaner will by default begin operation b) the vacuum cleaner operates poorly,
at the medium power range. 4 diodes will light on c) the dust bag is full.
the power level indicator (10). Filter disassembly
The suction power may be adjusted during operation.
The recommended settings are: Before changing the fi lters make sure that the vacuum
Setting 1 – vacuuming curtains cleaner is switched off and unplugged from the mains
Setting 2 – vacuuming upholstery supply.
Setting 3 – cost-effective power
Setting 4 – vacuuming carpets
05