MAINTENANCE / SERVICE
This tool is not intended for professional use
Before maintenance always switch Off tool, ensure
there is no water pressure in tool and hand gun,
disconnect plug from power source, and disconnect
tool from water supply
• Always keep tool and cord clean (especially ventilation
slots S 4))
- do not use water, solvents or polishes
regularly clean spraying nozzle G using cleaning
needle M @ (remove spray lance K from hand gun L
first)
Regularly check for worn Or damaged components and
have them repaired/replaced when necessary
Cleaning water filter
remove water filter E @ from inlet connector C @ with
long nose pliers
rinse it clean and put it back (replace it when
damaged)
! never use the tool with a damaged water filter
Storage @
store the tool out of reach of children in a location
where the ambient temperature will not exceed 400C
or drop below OOC
- do not place other objects on top of the tool
securely mount storage rail N on the wall with 4
screws (not supplied) and horizontally leveled
use storage rail N and storage straps P as illustrated
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on wuw.skil.com)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switch off the tool and disconnect the plug before
investigating the problem
Spray is not consistent
nozzle partly blocked -s clean nozzle
Motor does not Start Or stops suddenly
power supply socket faulty use another socket
plug not connected - connect plug
- thermal protection switched off the motor let the tool
cool down for 5 minutes
* Motor is running but spray is poor
nozzle completely blocked - clean nozzle
water tilter clogged clean water filter
air in the pump ensure that water inlet connector is
securely fitted
- inadequate water supply check that water tap is
fully open
ENVIRONMENT
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
symbol @ will remind you Of this when the need for
disposing occurs
C€ DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60335, EN 61000,
EN 55014 in accordance with the provisions Of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC,
2000/14,'EC, 2011/65/EU
Technical file at: SKIL Europe BV (PT-SEU/ENGI),
4825 BD Breda, NL
Marijn van der Hoofden
Operations & Engineering
Olaf Dijkgraaf
Approval Manager
SKIL Europe BV, 4825 BD Breda, NL
02.01.2013
NOISE/VIBRATION
ceo
Measured in accordance with EN 60704-1 the sound
pressure level of this tool is 81 dB(A) and the sound
power level 93 dB(A) (standard deviation: 2.2 dB), and
the vibration 2.5 rn/s2 (hand-arm method; uncertainty
K = 1.5 m/s2)
Measured in accordance with 2000/14/EC the
guaranteed sound power level LWA is lower than
97 dB(A) (conformity assessment procedure according to
Annex V)
The vibration emission level has been measured in
accordance with a standardised test given in
EN/lSO/5349; it may be used to compare one tool with
another and as a preliminary assessment Of exposure to
vibration when using the tool for the applications
mentioned
using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
8