• Cihazda tehlikeli bir durum görülmesi halinde, • Gaz kontrol düğmesi pilot alev konumuna
önce gaz ve elektrik bağlantısını kesiniz, sonra getiriliyor fakat alev almıyor ise gaz vanasını
yetkili servise haber vereniz. Ehliyetsiz kişilerin kontrol ediniz. Eğer kapalı ise açınız.
cihaza müdahale etmesine izin vermeyiniz. • Cihazın çalışması için tüm işlemleri (ısı seçimi,
pozisyon anahtarı konumu, pilotun yakılması)
yaptınız fakat cihaz yine çalışmıyor ise kapı tam
olarak kapatılmamış olabilir. Kapıyı kontrol edip
13. OLASI PROBLEMLER VE ÇÖZÜMLERİ kolunun tam yerine oturmasını sağlayınız.
• Tüm bunlara rağmen cihaz yine çalışmıyor ise
• Enerji lambası yanmıyor ise elektrik şalterini kontrol panosundaki arıza lambası yanacaktır. Bu
kontrol ediniz. durumda yetkili servise haber veriniz ve cihaza
hiç bir müdahalede bulunmayınız.
ÜRÜNLERIN KULLANIM ÖMRÜ 10 YILDIR.
GB
Please read these instructions carefully • The machine should be fed by 380-400V 3N AC
before using the appliance, and retain them 50-60Hz network voltage.
for future use. • Use cable of quality H07 RN-F and of crosscut
5x1.5mm2
1. INSTALLATION • Voltage tolerance should not be more than
• Rip off the protective nylon. If any sticky material ±10%. The machine must be earthed as DIN VDE
remains on, clean it with a suitable solvent. (e.g. 0100 clause 540.
Henkel - Helios) ATTENTION :Make sure that, after the
• Settle the appliance under a chimney hood as to electricity connection, the turning way of the
outlet the smoke, smell and the steam that come fan should be in the arrow direction. If it is
out during the cooking. reverse, the places of two phases should be
• If the smokes will forcedly be thrown out the changed.
electrical connection of the aspirator should be
common with the appliance. If there is no 4. GAS CONNECTION
ventilation the appliance should be stopped. At the • Before making the connection consult the gas
same time the absorption quantity should not be supplier.
more or less than the gas come out from the • Install a fast closing stopcock in an easily
appliance. accessible position upline from the appliance.
• Settle the appliance on a smooth and hard ground • Confirm the absence of leaks at the points of
with the help of its adjustable bases. connection.
• There should be a space of 60cm. at the left side • Confirm that the appliance is suitable for the type
of the appliance as to easily make the assembling of gas with which it will be supplied. If not, read
and maintenance. This will also make easy the air the paragraph “Modification for other type of
absorption of the motor. There should also be a gas”.
space of 10cm. at the back side for the air
circulation. 5. MODIFICATION FOR OTHER TYPE OF
• While setting the appliance, pay attention that the GAS
door of the appliance should be opened minimum • The appliance has been adjusted to operate with
1100 for an easy load and discharge. 30mbar LPG(G30).
• To adapt the appliance to another type of gas,
2. WATER CONNECTION carry out all the operations set out below.
• Make a water installation of 3/4" to the place • The nozzles, the minimum screws of the gas taps
where the machine is and connect a spherical which control the cooktop burners and the
valve. adhesive labels, are contained in a bag supplied
• The machine should be fed by 1.5-2 bar water at with the appliance.
5-7 0Fh. So, the jet of water will be prevented to Replacement of burner nozzles (Figure-1)
be limed in a short time.
3. ELECTRICAL CONNECTION • Remove the left side sheet.
• Unscrew nut which holds the nozzle. Take out “E”
• Connect the machine to a network proper to the
electric installation standards DIN VDE 0100. nozzle and choose the most suitable nozzle
indicated in table “T2”. Screw the nozzle by nut.
11