Kullanım Kılavuzları
NOTE: Please read these instructions completely GUARD FAN BLADE ASSEMBLY 2. Automatic 120-minute timer before operating this fan. Keep this manual for Fig1 Fig 2 1. Remove the spinner on the head unit byturning Turn the knob of the timer switch future reference. it clockwise. Then remove the plastic nut by to the right to set the timer. The C3 O turning it counterclockwise. maximum timer setting is 120 minutes. Turn the CHASSIS COLUMN UNITASSEMBLY 2. Place the rear guard to the head unit so that timer to 'ON 'to operate the fan without timer. 1. Unpack the packing box and check the parts -4 I the handle is upward. by referring to the part figure. From the column 3. Screw on the plastic nut (clockwise) securing Notes: unscrew the plastic nut. (See Fig.1) the fan guard on the head unit. 1. Do not turn the timer counter-clockwise for 2. Insert the column in the chassis and tighten .=. 4. Discard the small plastic sleeve located on the timer selection as this will damage it. the plastic nut.(If you can't tighten, check the motor shaft. 2. The fan will stop when the timer is in the nuts on the bottom of the chassis) (SeeFig.2) 5. Install the fan blade onto the motor shaft. "OFF" position. Please turn it to "ON" position 3. From the extension pole loosen the height Fig 3 Fig 4 Make sure the fan blade slot fits into the for operation. adjustment ring and adjust the internal pole retaining pin of the motor shaft. 3. Clutch knob to the desired height. (Note: If you can't find 6. Attach the spinner to the motor shaft by Press down this knob to oscillate the fan. To the internal pole, it slides inside the extension /3 I turning it counterclockwise to secure the fan choose one direction, pull up this knob when -4Z;- pole. You can pull it out from the extension blade. the fan is in the desired direction. pole.) (See Fig.3) 7.Place the circlip around the rear guard (You 4. Tilt adjusting 4. To attach the head unit to the column, loosen can skip this step if the circlip is already attached To adjust the airflow upward or downward, the thumb screw on the bottom of the head ii, to the rearguard.) push the guards lightlyto the desired direction. unit. 8.Secure both guards firmly by tightening the 5. Height adjusting 5. Place the head unit on the column and tighten fan guard then close easy clip. From the extension pole loosen the height the thumb screw in alignment with the groove adjustment ring and adjust the internal pole on the internal pole. (See Fig.4) i: OPERATING INSTRUCTION to the desired height. (See Fig.3) 1. Speed control Speed is controlled by pressing the buttons. 0-Off 1-Low2-Medium 3-High 7 8 120 WARNING MAINTENANCE INSTRUCTION 1. To reduce the risk of fire or electric shock, do The fan requires little maintenance. Do not try not use this fan with any solid state speed to repair it by yourself. Refer it to qualified service control device. personnel if service is needed. 2.If the supply cord is damaged, it must be 1. Unplug the unit during cleaning or assembling. replaced by the manufacturer or its service 2. Place the unit at least 10 cm away from the agent or a similarity qualified person in order wall to ensure adequate air circulation to the to avoid a hazard. motor. 3. Keep electrical appliances out of reach from Keep the vents of the rear motor cover (clean children or infirm person. Do not let them use from dust and fluff. the appliances without supervision. 3. Please wipe the exterior parts with a soft (cloth 4. Ensure that the fan is unplugged from the which soaked in mild detergent. Do not use main outlet before removing the guard. (any abrasive detergent or solvents to avoid (scratching the surface. Do not use any of the RULES FOR SAFETY OPERATION (following solution as cleaner gasoline. thinner, 1. Fan should be used under rated voltage. etc.) 2. Connect the fan to the power outlet after the 4. Do not allow water or any other liquid into fan is fully assembled. the (motor housing or interior parts. 3. Never insert fingers, pencils, or any other object through the guard when the fan is in operation. According to Waste of Electrical and Electronic 4.Unplug the fan from the outlet when it is not Equipment (WEEE) directive, WEEE should be in use. separately collected and treated. 5. Unplug the unit during cleaning or assembling. If at any time in future you need to dispose of 6. Be sure fan is on a stable surface when this product please do not dispose it with operating to avoid overturning. household waste. 7. DO NOT use fan in window. Rain may create Please send this product to WEEE collecting points electrical hazard. where available. 9 10