SAFETY USAGE RULES • Pis. urgently unplug your product if: • Rustproof, unperforated body is resistant HOW TO USE
Pis. read the safety usage rules below - The product works without any to strikes. • Your vacuum cleaner has different
carefully: interruption. • Radio, TV interference. accessories for variable (vacuuming. Please
• Yourvacuum cleaner is manufactured - After using • Both wet & dry cleaning. take care for choosing the accessory
according totechnical (and safety standards. - Before settling accessories (according to type of vacuuming. Ali the
• Always use your products at the same - Before cleaning ACCESSORIES accessories except the pipe and trunk are
voltage shown on (instruction manual and • If the cable is damaged, pis. unplug your Fabric Dust Bag (Picture 4) inside the main body. After getting off
product itself. product and go to (an authorized technical 100% polyester fabric dust bag can be your vacuum cleaner from gitf box, please
• You can use lengthening cable if you are service. washed by warm water with detergent for open the side locks and take out the motor
sure that it is safe. • Only use original accesories many times and be used again after drying. part (Please see picture 2) Take out all the
• Check all the filters and do not use without • Original spare parts have to be used for accessories inside the main body and fit
filters. repairing. the engine part to its place and close the
• Keep away your product from children • Ali repairing have to be done by authorized side locks.
• Do not keep the vacuuming pipe close to aftersale services,
ears and eyes
• Do not use for hot materials, acids, Your vacuum cleaner has made checked by
explosives, solvent, (abrasives cleaning af quality controls before offering to sales.
• Do not pull the cable while it is plugged • The motor with the by-pass system is
specially designed (according to
International standards and will not be Paper Dust Bag (Picture 5)
effected by the fluctuations of current You can use your paper dust bag if you do
voltage. not want to use fabric dust
• By-pass system allows the engine to cool • Gently fit the trunk to vacuuming hole
down with a (separate ventilator which (picture 3) and turn (right to be locked. Put
avoids the engine to burn out although the pipe at trunk. You can also use (only
vacuum system is closed by any way. one pipe or you can use without pipe and
• Vacuumed dusty air is filtered, cleaned and put the (accessories directly on trunk.
flown away (without touching the engine.
This will avoid collection of dust on the
engine and allows the engine to operate
long life.
• With it's variable filter system, it will not
flow the dust on (the engine and allows
the engine to operate long life.
8
To Operate The Vacuum Cleaner Cleaning Wet Surfaces Cleaning the main body
Please take into consideration that your Primarily the dust bags and all the accessories Float will close the sucking hole and stop
operating voltage is suitable for you vacuum of dry cleaning have not to be used while vacuuming when liquid increase the capacity
cleaner. Plug the cable on a wall electric cleaning wet surfaces. Pis. use rectangle level while liquid vacuuming. You have to
circuit and turn the switch to "0" position. vacuum accessory for cleaning ceramics, dispose the liquid to continue cleaning.
marbles Seperate the upper body from main
Manual Vacuum Control body and turn down. Gently push down the Warning!
Becasue of high vacuum power, while ejector on the sucking cover. Than pull out Dust bag has to be used on all cleaning except
vacuuming light materials like silk carpet, with a serewdriver or similar. After cleaning liquid vacuuming. If the float will go up and
curtain, fabric, etc., may be sucked inside the the sponge filter by shaking out. (picture 6) stop vacuuming at liquid vacuuming although
vacuum hole. You can open the vacuum settle the sucking cover to its place. it has not filled, pis. stop your vacuum
control manually to reduce the vacuum leaner and wait a while. The water on the
power to desired level. float will pour down and the float will go
down to its normal position.
CLEANING If your vacuum cleaner will turn over while
Emptying the body and cleaning filters liquid cleaning, the float will close the sucking
You do not need to clean your vacuum hole and stop vacuuming. Get your product
cleaner very often as it has a very large dust to upright position and wait for the float to
capacity. If the sucking power is reduced this go down to start vacuuming.
means the body is full or the filter has got
d i rty.
You have to empty the body or clean the
filter. You can wash your filter with warm
water if you want.
Warning! Do not forget to unplug your
product before
cleaning.
Float Filter
You have to clean the float filter when it get
dirty. Take off the float filter and wash it
with warm water and place it into its place
after drying.
10